Welcome to our site.
If you Need Something & Cant find it Anywhere else, or dont see it here, Give me an Email and I'll see If I can source it or what I can do.
Tool steels. I will have common sizes in stock and some off cuts. Spring steel for knives and tools I have loads of off cuts, if you have a shopping list to email, I'll try to fill it.
We do Buy, and sell second hand forge gear.
We do buy and source scrap metal for clients.
Stop In or Courier pick up is ok, or delivery may be available (charged), depending on your location and our orders..
Decorative iron. P.O.A.
This was forged by me for a parliament house display a while ago, when the display was over it went to a gallery.
As a very rough price guide for fence panels, a very basic panel 3000mm log by 1200mm tall using 40x10 for the bottom and mid rails, 16mm solid square bar as piquets, with welded finials, starting at about $2500.00 plus gst, undelivered, plus coatings.
Bees wax (for forge coating/finnishing steel).. 1kg Block $20.00.
Blacksmith beginner pack $130.00
1 tongs (P/up)
1 Cross pein hammer 2lb
2 chisels, (round punch, centre punch)
Anvil starter kit (Budget $100.) (solid $180)
1 bending fork
1 hardy cut off
Rivet/nail header sets (suit 8mm rod stock)
upsetting/ Block (1045 $20.00)
Standard Headers & Bolsters $45.00
(4 rivet sizes on the one plate) (20mm plate 1020)
rivet headers (5160 $20.00) (H13 $40.00) (4140 $30 )
Rivets ($1.00 ea)
Anvil mate tool (H feame tool) (Frame kits) $100.00
with cut off dies and plate mounted like the green machine $250.00
Hossfeld type, hobby size bender $250.00 With dies.
Need a tool rack? no space? got a trolly? Got an edge to hang something off? hang this on it..
Custom tool racks no problem on stands or rolling frames
(Tip: even dead office chair rolling stands make good tool caddies)
Tool Racks from $25.00
Castable, "1300" (1450 Deg C) , $55.00 +gst 25kg bag (this is a powder you add water to, and pour like concrete, so you will need some formers)....good for the pizza oven kits
Castable, 1600deg, $85.00 25kg inc. a bag (this is a powder you add water to, and pour like concrete, so you will need some formers).
Castable, "pyrocrete" 145 G, as above but troul or spray on or hand packable. (not runny) $60.00 inc (1 in stock)
Motar "Refractite" regular, 15kg pale premix ??.00 +gst
Fibre Blanket, 25mm heavy (128k) ($33.00 mtr X 600 wide) sold per metre or box,( IN STOCK )
Vacuum board 12mm $52. 1000mm X 610mm
Vacuum board 25mm $72. 1000mm X 610mm
Vacuum board 50mm $92. 1000mm x 610mm
kao grip 4 ltr 60.00+ gst (glue hi temp)
hardener 5ltr 75.00 + gst (protective coat)
Ceramic Fibre, 7.5mtr X 610mm X25 mm, box only
Fire Bricks, (in stock)
Fire Bricks 230mm x 115mm x 75mm Sold separately,,
light $9.00 ea
Heavy $11.00 ea
ITC-100 and ITC-213(metal parts coating)
Reflective Coat about $140 a pint delivered here.
(Prepaid, and cost adjusted at pick up)
Would have to work on a Swap Basis, If I can use the one you bring, I will or may have cut one of mine to your order. Minimum cutting fees of $40.00 Applies Plus Cleaning up. or you can take it away to clean it up.
Burners. (**Warning! I am not a gas fitter! the simple burner will not run on low without choofing. they will have to run from medium to high gas pressure. if in doubt, turn off gas supply at bottle and start again.**)I have a Simple Atmospheric Design(No Venturi) (from the Web) that runs fairly efitiently that I, or You can Make, or I'll Prepare The Parts for about $40.00, minus the gas fitting which you can buy unless pre-ordered, and you can weld/assemble it, if you like. I can Make and sell it for about $100.00. If you have a design, that you want us to make, We can cater for that as well.
Gas forges. I can make for about $800-$900.00 upwards. this give about a 13.5 w X 5 h X 9 inch deep cavity, with two machined burners. At the lower end of the slap together scale, coupla layers of ceramic wool treated with hardener and a brick in a gas bottle is about $350.00 (with burners).
I"ll be doing a diy kit, laser cut box ready to weld or bolt, and the bits to fill it and fire it.
The bigger furnace venturi burners are about $250.00, These sit on the floor or side mount and are about 50mm in dia. and about 350mm long to the elbow. ...or I can cut you a kit that you can roll the two cones and weld yourself. These do a 10-20kg ally melt
Side Note...These burners will need a bottle each to run, or the 45 kg bottle for more than one. I have two 9kg bottles and change over when the other freezes up. I use the four burners with four bottles. I use the red needle adj. regulators.
The "You Weld 'em" kit forges I make are a 8" x 8" down to 4" sqare(as per pic), 3" deep in a 6mm to 10-12mm plate and can suit round or sqare plumbing, ash dump and drain. basic kit without table is about $200.00. These are not too deep for charcoal and not too shallow for coke, and will get you forging.
coming soon, laser cut kits for forges and fire pot kits and componants for charcoal and coke depth, 50mm, 75mm deep and 110 mm deep forges , (these aren't cast and wont crack).
Assembled, table ready for a fan is about $600.00.
these I or you can make up for car blower to adapt to the forge
include a air gate and bolt ons ready for your fan to mount to
for about $200.00
This forge was built using all the hardware I make and sell, its the tool making and work forge and a copy of the one I use at home. These are available for hire, down to the smaller plough disk type.
Metal Offcuts of s/s, ally, steel, tupe, sheet, plate, solid. Send an Email request and i'll see if i can help.
12mm to 30mm plate..from $2.00 per kg
Old, new or used, forge gear, tools, anvils, vises.
Large lumps of Heavy Steel.
rail in stock
To suit the Engine Lift type Crane on Wheels. Clevis on bottom end.
( on order )
1 full set $10.00 (electrode, swirl ring, ceramic shield) (IN STOCK) 3 sets $22.00 (pic coming)
80 amp in stock also. (like trade tools. But cheaper!) (IN STOCK)
How Many Cans of Beetroot or Baked Beans Can You Eat!? And, How many times do you need a tin or an Ice Cream Container, or The Milo tin or Milk Bottle, or a Piece Of It, for a little job and need to ditch the tub? While your'e here...
$0.30 ea Some in stock again.
Don't Forget to Enquire As To What Other Wierd Bits We Might Have To Cater For Nick Nack Jobs. Or Just Ask...Ya Never Know.
These benders are $250.00 with yoke die and blocks.
Needle valve type funace lpg regulators to 15 and 15 to 30 PSI $90.00.